壓力開關信號波動較大的原因分析
1.當壓力開關在測量過程中出現了信號波動較大的情況時，首先應該檢查的是連接壓力開關的電源，查看電源的電流電壓是否正常，如果出現了過壓的現象，那出現信號波動較大的概率就會增加。
2.檢查被測介質的流速是否過快、流向是否相反如果有，應及時調整介質的流速與流向，盡量使得其符合壓力開關的應用要求。
3.查看壓力開關的各項參數，判斷是否有參數設置錯誤的情況，如果有，應重新設定參數，并嚴格按照調校方法進行調校，要注意調校開關或校驗開關時，必須保證開關與地面垂直。
西安仕樂克控制器制造有限公司 (www.a3025.cn)
[返回]
上一篇：不銹鋼壓力表的使用注意事項
下一篇：壓力開關的故障處理注意事項
相關文章
“shelok”牌西安仕樂克專業生產 壓力開關，智能壓力開關，差壓壓力開關，防爆壓力開關精度高，性能優，質量穩定，品種齊全，廣泛適用于石油、化工、冶金、電廠、醫藥等行業。
服務熱線：18092762450 傳真：傳真：029-88921196 聯系人:崔經理聯系電話：18092762450
Copyright © 2011-2012 版權所有 西安壓力開關廠 地址：西安市國際港務區新絲路產業園 主站蜘蛛池模板： | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |