耐震壓力表的安裝注意
1.安裝耐震壓力表之前，應首先核對該耐震壓力表的型號、規格、精度等級是否符合系統設備的使用要求，并同時檢查接口是否匹配，如果不匹配時，應及時通過轉換接頭進行轉換。
2.耐震壓力表在安裝時，應避免振動和碰撞，以免損壞其內部的零部件。
3.當耐震壓力表是需要垂直安裝在系統設備上時，它的傾斜度不可以超過30度，最好與設定點保持在同一水平線上，并盡量縮短距離，以免帶來指示誤差。
4.安裝完畢后，確保在無壓力的情況下，觀察壓力表的指針是否在零位上，如果指針有偏差，則代表安裝過程中出現問題，需要重新檢查安裝步驟。
5.當耐震壓力表需要測量帶特殊性質的介質時，以免對壓力表及使用設備都造成損壞。
西安仕樂克控制器制造有限公司 (www.a3025.cn)
[返回]
上一篇：壓力開關的選用與安裝
下一篇：機械壓力開關的日常管理
相關文章
“shelok”牌西安仕樂克專業生產 壓力開關，智能壓力開關，差壓壓力開關，防爆壓力開關精度高，性能優，質量穩定，品種齊全，廣泛適用于石油、化工、冶金、電廠、醫藥等行業。
服務熱線：18092762450 傳真：傳真：029-88921196 聯系人:崔經理聯系電話：18092762450
Copyright © 2011-2012 版權所有 西安壓力開關廠 地址：西安市國際港務區新絲路產業園 主站蜘蛛池模板： | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |