壓力開關電纜布線注意事項
壓力開關的安裝接線是壓力開關信號傳輸的重要環節之一，今天小編為大家介紹壓力開關布置電纜的注意事項。
1.壓力開關的傳感器與變送器之間通常都會有信號線和電源線兩根， 布線時，為了減少電源對信號輸出的干擾，信號線與電源線應該分別鋪設在不同管路中，另外信號線還應盡可能避免與電源線平行鋪設。
2.進行接線時，必須嚴格根據廠商提供的接線圖進行對號連接，不可錯亂連接。
3.接線完畢后，應將電纜包裝好，尤其是在潮濕的環境中，應該用塑料薄膜將電纜完整包裝，防止潮氣的侵入。
4.如果后期壓力開關出現故障需要檢查電纜時，檢修人員在檢查時，最好將電纜都按號進行標記，避免接線錯亂。
西安仕樂克控制器制造有限公司 (www.a3025.cn)
[返回]
上一篇：壓力開關安裝需知
下一篇：壓力開關的高低壓保護
相關文章
“shelok”牌西安仕樂克專業生產 壓力開關，智能壓力開關，差壓壓力開關，防爆壓力開關精度高，性能優，質量穩定，品種齊全，廣泛適用于石油、化工、冶金、電廠、醫藥等行業。
服務熱線：18092762450 傳真：傳真：029-88921196 聯系人:崔經理聯系電話：18092762450
Copyright © 2011-2012 版權所有 西安壓力開關廠 地址：西安市國際港務區新絲路產業園 主站蜘蛛池模板： | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |